ARCOR 25551 Quick-Set
GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY REBUILDING COMPOUND
DESCRIPTION AND RECOMMENDED USES: ARCOR™25551 Quick-Set is a solvent free two-component, moisture insensitive epoxy adhesive designed as an emergency repair or bonding material for metals, glass, concrete or wood. ARCOR™25551 Quick-Set sets in 5 minutes and can get put in service within 1 hour regardless of temperature. ARCOR™25551 Quick-Set has good resistance in a wide variety of chemical environments and has heat resistance to 450ºF. ARCOR™25551 Quick-Set is an easy to use 1:1 mix ratio and can be applied overhead or vertically. Conveniently packaged in two tubes of resin and hardener. Squeeze equal portions on a nonporous surface and mix thoroughly.
FOR INDUSTRIAL USE ONLY
TEMPERATURE: Immersion service
Max. 200ºF (93ºC) ; Dry to 450ºF (232ºC)
Alkalies: Very Good
Inorganic Acids: Good
Organic Acids: Fair
Organic Solvents: Good
BOND STRENGTH: 3,000 psi @ 2 hours 3,600 psi @ 24 hours
FILM THICKNESS: up to 1000 mils/coat
APPLICATIONS: Repair burst pipes, tanks, pumps and the like which contain liquids or gases. Use for bonding Dissimilar Metals. Use for Concrete, Metal, Glass, Wood.
SOLIDS BY VOLUME: 100%
POT LIFE: 3-5 MIN @ 72ºF
MIX RATIO: 1:1 by Volume (Base:Activator)
SHELF LIFE: 5 Years at 55-95ºF (13-35ºC)
COVERAGE: varies with thickness applied
WEIGHT: 100 grams per 3 oz tube; 200 grams total kit, OR 180 grams per 5 oz tube; 360 grams total kit.
To place orders and/or obtain pricing information contact:
ARCOR Epoxy Inc.
PO Box 273
South Dennis, MA 02660
Email: [email protected]; Tel: 508-385-5598
Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.
SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT
For best results clean area to be repaired to remove loose dirt, scale and oils. Use MEK or a simular solvent and a degreaser if oils are present. If possible sand or grind the area with course paper or disk.
Thoroughly mix Activator into Base with mixing stick scraping sides and bottom of container or mixing board. Mix by volume 1 parts Base to 1 part Activator. Mix thoroughly to produce an even colored, streak-free material.
If desired, thin with Kelone blend from 5% to 7.5% by volume
Use heavy plastic squeegee or putty knife. Work material into profile of substrate to achieve maximum adhesion and to remove any entrapped air. Contour to correct form with putty knife or plastic applicator. If mold or form is used, coat its surface with a release agent to prevent adhesion of the material. Machining is possible using diamond tipped tools only. Sanding/Grinding is possible if done within 1 hour of application at 77ºF, 25ºC. Caution: Material cures rapidly. Use only the quantity of material which can be easily applied within 4 to 5 minutes. Spreading mixed material on a mixing board or other flat surface will extend the working life. Large holes and cracks can be bridged with glass or metal cloth.
Material: Keep between 55 to 95ºF (17 to 35ºC). Substrate: keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of the substrate and the material should never exceed 10ºF, 5ºC. Substrate shall be a minimum of 5ºF (3ºC) above dew point. Do not apply if relative humidity exceeds 90%. If necessary heat the metal prior to surface preparation using electric heater or heat lamp. Never use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area overnight (75ºF+) for ease of mixing. If necessary Base component of material can be heated by microwave for 30-45 seconds for a 1 KG Base unit or by warm water bath. Heat activated by warm water bath only. If necessary let material cool before application. Caution: Material cures rapidly. Use only the quantity of material which can be easily applied within 4 to 5 minutes. Heating will accelerate cure time.
OVERCOAT / CURE TIME:
Recoat as soon as possible while material is still soft, within 1 hour at 77ºF, 25ºC. If overcoat window is exceeded abrade surface with course sandpaper, grinder or brush blast. Full cure before immersion 45 minutes at 77ºF. Add 10 minutes additional cure time for each 10ºF below 77ºF. Subtract 15 minutes of cure time for each 10ºF above 77ºF.
CLEAN UP: Clean tools immediately after use with M.E.K., Acetone or similar
WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention.