ARCOR Header

ARCOR EE 75

Data Sheet

REVISED 5/2014

GENERIC TYPE: 100% SOLIDS EPOXY FLOORING; PRIMER, TOPCOAT

DESCRIPTION AND RECOMMENDED USES: ARCOREE-75 is a solvent free, low viscosity epoxy coating suitable for flooring, particularly in chemically aggressive environments whether acid, caustic or solvent. ARCOREE-75 produces a tough, chemical resistant coating on all types of concrete substrates, asphalts or steel. As clear a low viscosity epoxy ARCOREE-75 is suitable for use with broadcast colored quartz flooring.

FOR INDUSTRIAL USE ONLY

SPECIFICATION DATA:

TEMPERATURE: Immersion service

200ºF(93ºC);Spike to 250ºF(121ºC) (3 Hrs) Dry 325ºF(163ºC);Spike to 375ºF(191ºC) (3 Hrs)

 

CHEMICAL RESISTANCE:

Water:                             Excellent

Alkalies:                          Excellent

Inorganic Acids:            Excellent

Organic Acids:               Good

Organic Solvents:          Excellent

 

ABRASION:  Very Good

FILM THICKNESS: 20 mils(.52 mm)/coat Exterior: 2 coats, Immersion: 2-3 coats

FLEXIBILITY: Good Excellent with Fiberglass Mat; 1.5 oz/ft2 (.5 KG/M2)

APPLICATIONS: Aggressive Chemical Secondary Containment Areas, Industrial Floorings.

SOLIDS BY VOLUME: 100%

VISCOSITY: 1,000-1,500 cps

POT LIFE: 35 MIN @ 72ºF

MIX RATIO: 3:2 by Volume (Base:Activator) 100 gm: 59 gm by Weight

COLOR:  Clear (not pigmented)

SHELF LIFE:  5 Years at 55-95ºF (13-35ºC)

COVERAGE: 80 ft2(7.5 M2)/gal/coat(theoretical)

WEIGHT PER GALLON: 9.1 lbs (4.13 KG)

 

ORDER INFORMATION:

To place orders and/or obtain pricing information contact:

ARCOR Epoxy Inc. PO Box 273

South Dennis, MA 02660

TEL: 800-878-9593; FAX: 888-878-9593

Contact Us!

Manufacturer makes no warranty either expressed or implied including warranties of merchant ability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.

APPLICATION SHEET

REVISED 5/2014

SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT

 

SURFACE PREPARATION:

Steel floor surfaces are to be abrasive blasted with chloride free abrasive to SSPC SP-6 Commercial gray metal finish. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted surfaces to be primed with 10 mils of ARCOREE- 75 or EE-79 followed by a 20 mil Topcoat of ARCOREE-75.

Concrete floor surfaces should be degreased if oil and grease contamination is present. Grind down all high points and protrusions with course aluminum oxide grind disks or scarrifier. Abrasive blast entire surface with open blast or BlasTrac. Hand grind or scarrify all hard to reach areas. Blast should remove all surface laitance, existing coatings and any mastics giving a clean profiled concrete. Prime all areas with 10 mils of ARCOREE-75 or EE-79 followed by a 20 mil Topcoat of ARCOREE-75.

MIXING:

Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade. Mix by Volume 3 parts Base to 2 part Activator or by weight 100 grams base to 59 grams activator.

THINNING:

Never thin.

APPLICATION:

Brush use medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Roller use good quality 1/4” nap on concrete.

Floor squeegee use hard rubber ‘notched’.

Plural Spray use .017-.019 tip, 2,000-2,500 PSI, Heat to 100ºF Base, 100ºF Activator. Airless Spray use .017-.021 tip, 2,000-2,500 PSI(Caution: Short Pot-Life) Conventional Spray: Not Recommended

All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate contamination.

APPLICATION TEMPERATURE:

Material: Keep between 55 to 95ºF(13 to 35ºC). Substrate : Keep between 45 to 105ºF(7 to 40ºC). The difference in tem- perature of the substrate and the coating should never exceed 10ºF (5ºC).

OVERCOAT/CURE TIME:

Brush or Roller recoat between 2 and 14 hours at 77ºF (25ºC).

Full cure before chemical exposure or high stress; 24 Hours at 77ºF. Force Cure: 12 hours at 150ºF (66ºC); 6 hours at 200ºF (93ºC).

 

CLEAN UP: M.E.K., Acetone or similar. In solvent controlled environments Isopropyl Alcohol can be used.

 

WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention.

Product Photos:

Related Cases:

Related Links:

Related Videos: