ARCOR Header

ARCOR EE 97

Data Sheet

SDS Sheet

REVISED 4/2013

GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY REBUILDING COMPOUND

DESCRIPTION AND RECOMMENDED USES: ARCOR™ EE-97 is a solvent free, two-component, stainless steel rein- forced rebuilding compound which can be used to repair any metal surface that has been damaged, cracked or worn. ARCOR™ EE-97 is non-sagging up to 200 mils, will not shrink when curing, has excellent adhesion to all metal surfaces, is machinable with carbide or high speed cutting tools and can be drilled, tapped or sanded. ARCOR™ EE-97 has excel- lent resistance in a wide variety of chemical environments and has heat resistance to 450ºF.

FOR INDUSTRIAL USE ONLY

SPECIFICATION DATA:

TEMPERATURE: Immersion service

Max.265ºF; Dry to 450ºF

 

CHEMICAL RESISTANCE:

Water:                                Excellent

Alkalies:                             Very Good

Inorganic Acids:               Very Good

Organic Acids:                  Fair

Organic Solvents:            Good

 

ABRASION: Excellent

FLEXIBILITY: Fair

FLEXURAL STRENGTH: 13,500 psi (ASTM D790/7 days)

COMPRESSIVE STRENGTH: 17,200 psi (ASTM D695/7 days)

TENSILE SHEAR: 2,400 psi (ASTM D1002/steel:steel)

APPLICATIONS: Worn Shafts, Hydraulic Rams, Keyways,Pumps, Valves, Impellers, Propellers, Stripped Threads, Cracked Engine Blocks.

SOLIDS BY VOLUME: 100%

VISCOSITY: Paste

DENSITY: 1.70

POT LIFE: 20 Min/KG @ 75ºF

MIX RATIO: 1:1 by volume (Base:Activator) 100 gm : 100 gm by weight

COLOR:  Gray

SHELF LIFE: 5 Years at 55-95ºF, 13-35ºC

COVERAGE: Varies with thickness applied

WEIGHT PER GALLON: 12.6 (5.71 KG)

FILM THICKNESS: 100-200 mils/coat

 

ORDER INFORMATION:

To place orders and/or obtain pricing information contact:

ARCOR Epoxy Inc. PO Box 273

South Dennis, MA 02660

TEL: 800-878-9593; FAX: 888-878-9593

Contact Us!

Manufacturer makes no warranty either expressed or implied including warranties of merchant ability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.

APPLICATION SHEET

 REVISED 4/2013

 SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT

 

SURFACE PREPARATION:

Metal surfaces are to be cleaned and degreased then abrasive blasted with chloride free abrasive. Exterior applications to SSPC SP-10 Near White metal finish minimum 3 mil profile. Immersion applications to SSPC SP-5 White metal, 3 to 5 mil profile. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted surfaces to be rebuilt as quickly as possible to prevent oxidation of surface. For larger surface areas with ferrous metals if need prime with S-30 Prime or EE-11 Prime.

MIXING:

Thoroughly mix Activator into Base with mixing stick scraping sides and bottom of container or mixing board. Mix by Volume 1 parts Base to 1 part Activator. Or by Weight 1 parts Base to 1 part Activator (100:100). Mix thoroughly to pro- duce an even colored, streak-free material.

THINNING:

Never thin.

APPLICATION:

Use heavy plastic squeegee or putty knife. Work material into profile of substrate to achieve maximum adhesion and to remove any entrapped air. Contour to correct form with putty knife or plastic applicator. If a mold or form is used be sure to coat its surface with a release agent to prevent adhesion of the material. Machining is possible using diamond tipped tools only. Sanding or Grinding is possible only if done within 6 hours of application at 77ºF (add 1 hour for each 10ºF below 77º, subtract 1/2 hour for each 10ºF above 77ºF). Large holes and cracks can be bridged with glass or metal cloth.

APPLICATION TEMPERATURE:

Material: Keep between 55 to 95ºF(17 to 35ºC). Substrate: Keep between 45 to 105ºF(7 to 40ºC). The difference in tem- perature of the substrate and the material should never exceed 10ºF, 5ºC. Substrate shall be a minimum of 5ºF(3ºC) above dew point. Do not apply if relative humidity exceeds 90%. If necessary heat the metal prior to surface preparation using electric heater or heat lamp. Never use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area overnight(75ºF+) for ease of mixing. If necessary Base compo- nent of material can be heated by microwave for 30-45 seconds for a 1 KG Base unit or by warm water bath. Heat activa- tor by warm water bath only. If necessary let material cool before application.

OVERCOAT / CURE TIME:

Recoat as soon as possible while material is still soft, within 4 to 6 hours at 77ºF. 25ºC. If overcoat window is exceeded abrade surface with course sandpaper, grinder or brush blast. Full cure before immersion 36 hours at 77ºF. Add 1 day additional cure time for each 10ºF below 77ºF. Subtract 6 hours of cure time for each 10ºF above 77ºF. Force Cure with heat for best performance for 1 hour at 200ºF, 93ºC, 12 hours at 120ºF, 49ºC.

 

CLEAN UP: Clean tools immediately after use with M.E.K., Acetone or similar.

 

WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention.

Product Photos:

Related Cases:

Related Links:

Related Videos: