fbpx

2213 Epoxy Stick

ARCOR Header

ARCOR 2213 Epoxy Stick
Updated May 2020

None

GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY REBUILDING COMPOUND

DESCRIPTION AND RECOMMENDED USES: 2213 Stick is a solvent free two-component, moisture insensitive epoxy adhesive designed as an emergency repair or bonding material for metals, glass, concrete, or wood. It is corrosion resistant, steel reinforced and can be sanded & tooled. In Single Stick form it is easily carried and can be kneaded by hand. 2213 sets in 5 minutes and can get put in service withing 1 hour regardless of temperature.
NSF Standard 61 Potable Water; USDA incidental meat & poultry contact.

FOR INDUSTRIAL USE ONLY

SPECIFICATION  DATA:

TEMPERATURE: Immersion service Max. 130ºF (54ºC) ; Dry continuous to 250ºF (121ºC)

ABRASION: Excellent

FLEXIBILITY: Fair

SOLIDS BY VOLUME: 100%

VISCOSITY: Putty

POT LIFE: 3-5 MIN/KG @ 72ºF

MIX RATIO: 1:1 by Volume (Base:Activator) 100 gm: 100 gm by weight

COLOR: Gray

FILM THICKNESS: up to 1000 mils/coat

BOND STRENGTH: 3,000 psi @ 2 hours ; 4,200 psi @ 24 hours

SHELF LIFE:  5 Years at 55-95ºF  (13-35ºC)

COVERAGE: varies with thickness applied

WEIGHT PER GALLON: 7″ ; 4 oz stick

COMPRESSIVE STRENGTH: 12,000 psi

HARDNESS: 80 shore D (full cure @ 1 hr)

DIELECTRIC: 300 volts/mil

APPLICATIONS: Repair burst pipes, tanks, pumps and the which contain liquids or gases, use for bonding dissimilar metals, use for concrete, metal, glass, wood

APPLICATION SHEET

REVISED 2/2014

SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT

SURFACE PREPARATION: For best results clean area to be repaired to remove loose dirt, scale and oils. Use MEK or a similar solvent and a degreaser if oils are present. If possible sand or grind the area with course paper or disk.

MIXING: Break off the required amount from the tube. Knead by hand thoroughly to produce ab even colored, streak-free material. Recommended use of lightweight rubber or latex gloves to prevent any skin irritation.

THINNING: If desired, thin with Kelone blend from 5% to 7.5% by volume

APPLICATION: Use heavy plastic squeegee or putty knife. Work material into profile of substrate to achieve maximum adhesion and to remove any entrapped air. Contour to correct form with putty knife or plastic applicator. If mold or form is used, coat its surface with a release agent to prevent adhesion of the material. Machining is possible using diamond tipped tools only. Sanding/grinding is possible if done within 1 hour of application at 77ºF, 25ºC. Caution: Material cures rapidly. Use only the quantity of material which can be easily applied within 4 to 5 minutes. Spreading mixed material on a mixing board or other flat surface will extend the working life. Large holes and cracks can be bridged with glass or metal cloth.

APPLICATION TEMPERATURE: Material: Keep between 55 to 95ºF (17 to 35ºC). Substrate: Keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of   the substrate and the material should never exceed 10ºF (5ºC). Substrate shall be a minimum of 5ºF (3ºC) above dew point. Do not apply if relative humidity exceeds 90%. If necessary heat metal prior to surface preparation using electric heater or heat lamp. Never use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area overnight (75ºF+, 24ºC) for ease of mixing. If necessary Base component of material can be heated by microwave for 30 seconds for a 1 MK Base unit or by warm water bath. Heat activator by warm water bath only. If necessary let material cool before application.

OVERCOAT/CURE TIME: Recoat as soon as possible while material is still soft, within 1 hour at 77ºF (25ºC). If overcoat window is exceeded abrade surface with course sandpaper, grinder or brush blast. Full cure before immersion 45 minutes at 77ºF. Add 10 minutes additional cure time for each 10ºF below 77ºF. Subtract 15 minutes of cure time for each 10ºF above 77ºF.

CLEAN UP: Clean tools immediately after use with M.E.K., Acetone or similar

WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention.

Are you interested in this product?
Want to know more?

To place orders and/or obtain pricing information contact or call our offices below:

Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.