ARCOR 1321K (Kevlar)
Updated May 2020
GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY PRIMER, TOPCOAT
DESCRIPTION AND RECOMMENDED USES: ARCOR® 1321K is a solvent free bisphenol F coating suitable for immersion and non-immersion service, particularly in aggressive environments. ARCOR® 1321K is self-priming and produces a tough, chemical resistant coating on ferrous & non-ferrous metals and concrete. As a low viscosity epoxy with excellent flexibility ARCOR® 1321K is especially suitable for external applications with aggressive exposures. Suitable for hand or spray application on metals or concrete. The long pot-life and over coat window make this ideal for larger surface area application by airless or plural component spray. Excellent UV stability. The addition of Kevlar® (DuPont registered trademark) improves resistance to impact, abrasion, flex, while still maintaining the ability to spray.
FOR INDUSTRIAL USE ONLY
TEMPERATURE: Immersion service
Max.145ºF (49ºC); Spike to 200ºF (79ºC)(3 Hrs). Dry to 325ºF (149ºC)
SOLIDS BY VOLUME: 100%
VISCOSITY: 10,000-18,000 cps
POT LIFE: 35 MIN/KG @ 72ºF
MIX RATIO: 2:1 by Volume (Base:Activator) 100 gm: 36 gm by weight
COLOR: Blue, Gray, Light Gray, Black, White; Yellow;
FILM THICKNESS: Can be applied up to 20 mils in a single coat. Single coat spray application. Hand application may require a 2nd coat.
FLEXIBILITY: Very Good
Excellent with Polyester Cloth; 1.5 oz/ft 2(.5 KG/M2)
APPLICATIONS: Ideal for exterior applications to resist exposure to Salt Water; Caustics, Alcohols, Acids. Also suitable for immersion service in water (brakish, salt) and Caustics.
Excellent for Secondary Containment’s.
SHELF LIFE: 5 Years at 55-95ºF (13-35ºC)
COVERAGE: 80 ft2 (7.5M2)/ gal / coat @ 20 mils
WEIGHT PER GALLON: 11.6 lbs (5.27 KG), 231 cu.in.)
SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT
SURFACE PREPARATION: Steel surfaces are to be abrasive blasted with chloride free abrasive. Exterior applications to SSPC SP-10 Near White metal finish. Immersion applications to SSPC SP-5 White metal 3 to 5 mil profile. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted ferrous surfaces to be should be coated immediately with ARCOR™ 1321K to prevent oxidation of surface. For very large areas ARCOR™ EE-80 can be used as a pre-prime to help hold the blast.
Concrete surfaces should be degreased if oil and grease contamination is present. Degreased surface shall be high pressure washed, acid etched and high pressure washed again so surface is clean and free of all grease, oils and surface laitance. Existing coatings should be abrasive blasted to clean concrete. Prime with ARCOR™ 1321K.
MIXING: Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mixing board. Mix by Volume 2 parts Base to 1 part Activator. Or by weight 100 grams base to 36 grams activator. Mix thoroughly to produce an even colored and streak-free material.
THINNING: Not Advised; but if necessary add 5% by volume (6oz/gal.) Acetone or MEK to extend pot-life and/or thin for cold weather application.
APPLICATION: All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate contamination.
Brush: medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Trim or tape to <1” nap. Roller: good quality 3/8” nap.
Plural Spray: .031-.035 tip, 2,200-3,500 PSI, Heat to 130ºF Base, 100ºF Activator. 30 mesh screens. Heated hose @ 140ºF Airless Spray: .031-.039 tip, 4,000-4,500 PSI(45:1). Add 6-oz/gal of MEK or Acetone.(Caution: Short Pot-Life)
Conventional Spray: Not Recommended.
APPLICATION TEMPERATURE: Material: Keep between 55 to 95ºF (17 to 35ºC). Substrate: Keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of the substrate and the material should never exceed 10ºF (5ºC). Substrate shall be a minimum of 5ºF (3ºC) above dew point. Do not apply if relative humidity exceeds 90%. If necessary heat metal prior to surface preparation using electric heater or heat lamp. Never use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area overnight (75ºF+, 24ºC) for ease of mixing. If necessary Base component of material can be heated by microwave for 30 seconds for a 1 MK Base unit or by warm water bath. Heat activator by warm water bath only. If necessary let material cool before application.
OVERCOAT/CURE TIME: By brush, roller or squeegee re-coat while material is still soft, but tack-free, between 1-12 hours at 77ºF (25ºC). If overcoat window is exceeded abrade surface with course sandpaper, grinder or brush blast. By spray application a single coat to 20 mils is recommended. For multiple coats, re-coat between 1-12 hours at 72ºF. Full cure before chemical immersion 72 hours at 72ºF. Add 12 hours additional cure time for each 10ºF below 72ºF. Subtract 12 hours of cure time for each 10ºF above 72ºF. Force Cure with heat for best performance for 4 hours at 150ºF (66ºC), 12 hours at 100ºF ( 38ºC).
CLEAN UP: Clean tools immediately after use with M.E.K. or similar. Isopropyl Alcohol can be used in solvent restricted areas.
WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention.
Are you interested in this product?
Want to know more?
To place orders and/or obtain pricing information contact or call our offices below:
Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.