fbpx
  • PO Box 990, Harwich, MA 02645, USA
ARCOR Header

ARCOR EE-10.5

GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY PRIMER, TOPCOAT

DESCRIPTION AND RECOMMENDED USES: ARCOR™ EE-10.5 is a solvent free, high functionality epoxy Novolac coating suitable for immersion and non-immersion service, particularly in aggressive acid environments. ARCOR™ EE-10.5 produces a tough, chemical resistant coating on ferrous and non-ferrous metals and concrete. As the lowest viscosity epoxy Novolac available ARCOR™ EE-10.5 is suitable as a primer as well as a topcoat. Excellent for 98% Sulfuric Acid immersion.

FOR INDUSTRIAL USE ONLY

SPECIFICATION DATA:

TEMPERATURE: Immersion service

Max. 250ºF (121ºC); Spike to 300ºF (149ºC) With force cure at 200ºF, 6 Hrs.

SOLIDS BY VOLUME: 100%

VISCOSITY: 9,000-15,000 cps

POT LIFE: 25 MIN @ 72ºF

MIX RATIO: 2:1 by Volume (Base:Activator) 100 gm: 50 gm by Weight

COLOR: Clear Amber (not pigmented)

ABRASION:  Very Good

FILM THICKNESS: 8-10 mils(.26 mm)/coat Exterior: 2 coats, Immersion: 2-3 coats

Flexibility: Very Good

Applications: 98% Sulfuric, Aggressive Chemical Tank Linings and Secondary Containment Areas, Industrial Floorings. Excellent when Force Cure is not available.

SHELF LIFE:  5 Years at 55-95ºF (13-35ºC)

COVERAGE: 160 ft2 (15 M2)/gal/coat (theoretical)

WEIGHT PER GALLON: 9.3 lbs (4.35 KG)

Manufacturer, Novolac Epoxy Technologies Inc., makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Novolac Epoxy Technologies Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer. ARCOR® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets and any other information as supplied in writing directly from manufacturers technical support.

APPLICATION SHEET

REVISED 5/2013

SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT

SURFACE PREPARATION: Steel surfaces are to be abrasive blasted with chloride free abrasive. Exterior applications to SSPC SP-6 Commercial gray metal finish. Immersion applications to SSPC SP-5 White metal. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted surfaces to be primed with ARCOR™ EE-10.

Concrete surfaces should be degreased if oil and grease contamination is present. Degreased surface shall be high pres- sure washed, acid etched and high pressure washed again so surface is clean and free of all grease, oils and surface laitance. Existing coatings should be abrasive blasted to clean concrete.

MIXING: Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade. Mix by Volume 2 parts Base to 1 part Activator. Or by weight 100 grams base to 50 grams activator. Mix thoroughly to produce and even colored, streak- free material.

THINNING: Never thin.

APPLICATION: All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate contamination.

By brush use medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Trim or tape to <1” nap.

Roller use good quality 1/8” nap, 1/4” on concrete.

Plural Spray use .017-.019 tip, 2,000-2,500 PSI, Heat to 120ºF Base, 100ºF Activator. Airless Spray use .017-.021 tip, 2,000-2,500 PSI(Caution: Short Pot-Life) Conventional Spray: Not Recommended

APPLICATION TEMPERATURE: Material: Keep between 55 to 95ºF (13 to 35ºC). Substrate : Keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of the substrate and the coating should never exceed 10ºF (5ºC).

OVERCOAT/CURE TIME: Brush or Roller re-coat between 6 and 14 hours at 77ºF (25ºC).

Spraying re-coat between 3 and 14 hours. Full cure before immersion 7 Days at 77ºF.

Force Cure: 12 hours at 150ºF (66ºC); 6 hours at 200ºF (93ºC).

CLEAN UP: Clean tools immediately after use with M.E.K., Acetone, 98+% Isopropyl Alcohol or similar

WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention. Consult the Product Safety Data Sheets (SDS) BEFORE USE!

The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Novolac Epoxy Technologies Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer.

Are you interested in this product?
Want to know more?

To place orders and/or obtain pricing information contact or call our offices below:

Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. ARCOR® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets and any other information as supplied in writing directly from manufacturers technical support.