
GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY 3.6 NOVOLAC PRIMER, TOPCOAT
DESCRIPTION AND RECOMMENDED USES: ARCOR® EE-101 HT is a solvent free, Ultra 3.6 functionality epoxy Novolac coating. It’s designed for use in the most aggressive chemical and high temperature environments typically thought beyond the abilities of epoxies. ARCOR® EE-101 HT can be used on ferrous and non- ferrous metals and concrete. Excellent for Nitric, Hydrochloric, Glacial Acetic Acid and Methanol. As the lowest viscosity epoxy 3.6 functionality Novolac available ARCOR® EE-101 HT is suitable as a primer as well as a topcoat. The absence of fillers and pigments make it the highest performing Novolac coating commercially available.
FOR INDUSTRIAL USE ONLY
SPECIFICATION DATA:
TEMPERATURE: Immersion service
Max.350F(177ºC); Spike to 450ºF(3 Hrs) Recommended force cure at 250ºF@ 2 hrs.
SOLIDS BY VOLUME: 100%
VISCOSITY: 9,000-15,000 cps
POT LIFE: 15 MIN @ 72ºF
MIX RATIO: 3:1 by Volume (Base:Activator) 100gm: 27 gm by Weight
COLOR: Clear Amber (not pigmented)
ABRASION: Good
FILM THICKNESS: 8-10 mils (.26 mm)/coat Exterior: 2 coats, Immersion: 2-3 coats
Flexibility: Good
APPLICATIONS: Aggressive Chemical Tank Lings and Secondary Containment Areas. Excellent when Force Cure is not available.
SHELF LIFE: 5 Years at 55-95ºF (13-35ºC)
COVERAGE: 160ft² (15M²)/gal/coat(theoretical)
WEIGHT PER GALLON: 9.5lbs (4.30 KG)
Manufacturer, Novolac Epoxy Technologies Inc., makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Novolac Epoxy Technologies Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer. ARCOR® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets and any other information as supplied in writing directly from manufacturers technical support.
APPLICATION SHEET
REVISED 6/2013
SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT
SURFACE PREPARATION: Steel surfaces are to be abrasive blasted with chloride free abrasive. Exterior applications to SSPC SP-6 Commercial gray metal finish. Immersion applications to SSPC SP-5 White metal. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted surfaces to be primed with ARCOR® EE-101. Concrete surfaces should be degreased if oil and grease contamination is present. Degreased surface shall be high pressure washed, acid etched and high pressure washed again so surface is clean and free of all grease, oils and surface laitance. Existing coatings should be abrasive blasted to clean concrete.
MIXING: Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade. Mix by Volume 3 parts Base to 1 part Activator. Or by weight 100 grams base to 27 grams activator.
THINNING: Never thin.
APPLICATION: By brush use medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Trim or tape to <1” nap. Roller use good quality 1/8” nap, 1/4” on concrete.
Plural Spray use .021-.027 tip, 3,000-3,500 PSI, Heat to 120ºF Base, 100ºF Activator. Airless Spray: Not recommended
Conventional Spray: Not Recommended All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate contamination.
APPLICATION TEMPERATURE: Material: Keep between 55 to 95ºF (13 to 35ºC). Substrate : Keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of the substrate and the coating should never exceed 10ºF (5ºC).
OVERCOAT/CURE TIME: Brush or Roller re-coat between 2 and 8 hours at 77ºF (25ºC).
Spraying re-coat between 1 and 4 hours. Full cure before immersion 36 Hours at 77ºF. Force Cure: 8 hours at 120ºF (49ºC); 2 hours at 250ºF (121ºC)
CLEAN UP: Clean tools immediately after use with M.E.K., Acetone, 98+% Isopropyl Alcohol or similar
WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention. Consult the Product Safety Data Sheets (SDS) BEFORE USE!
The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Novolac Epoxy Technologies Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer.

Are you interested in this product?
Want to know more?
To place orders and/or obtain pricing information contact or call our offices below:
Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. ARCOR® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets and any other information as supplied in writing directly from manufacturers technical support.