ARCOR EE-75
GENERIC TYPE: 100% SOLIDS EPOXY FLOORING; PRIMER, TOPCOAT
DESCRIPTION AND RECOMMENDED USES: ARCOR™ EE-75 is a solvent free, low viscosity epoxy coating suitable for flooring, particularly in chemically aggressive environments whether acid, caustic or solvent. ARCOR™ EE-75 produces a tough, chemical resistant coating on all types of concrete substrates, asphalts or steel. As clear a low viscosity epoxy ARCOR™ EE-75 is suitable for use with broadcast colored quartz flooring.
FOR INDUSTRIAL USE ONLY
SPECIFICATION DATA:
TEMPERATURE: Immersion service
200ºF(93ºC);Spike to 250ºF(121ºC) (3 Hrs) Dry 325ºF(163ºC);Spike to 375ºF(191ºC) (3 Hrs)
ABRASION: Very Good
FILM THICKNESS: 20 mils(.52 mm)/coat Exterior: 2 coats, Immersion: 2-3 coats
FLEXIBILITY: Good Excellent with Fiberglass Mat; 1.5 oz/ft2 (.5 KG/M2)
APPLICATIONS: Aggressive Chemical Secondary Containment Areas, Industrial Floorings.
SOLIDS BY VOLUME: 100%
VISCOSITY: 1,000-1,500 cps
POT LIFE: 35 MIN @ 72ºF
MIX RATIO: 3:2 by Volume (Base:Activator) 100 gm: 59 gm by Weight
COLOR: Clear (not pigmented)
SHELF LIFE: 5 Years at 55-95ºF (13-35ºC)
COVERAGE: 80 ft2 (7.5 M2)/gal/coat(theoretical)
WEIGHT PER GALLON: 9.1 lbs (4.13 KG)
Manufacturer, Novolac Epoxy Technologies Inc., makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Novolac Epoxy Technologies Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer. ARCOR® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets and any other information as supplied in writing directly from manufacturers technical support.
APPLICATION SHEET
REVISED 5/2014
SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT
SURFACE PREPARATION: Steel floor surfaces are to be abrasive blasted with chloride free abrasive to SSPC SP-6 Commercial gray metal finish. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted surfaces to be primed with 10 mils of ARCOR™ EE- 75 or EE-79 followed by a 20 mil Topcoat of ARCOR™ EE-75.
Concrete floor surfaces should be degreased if oil and grease contamination is present. Grind down all high points and protrusions with course aluminum oxide grind disks or scarrifier. Abrasive blast entire surface with open blast or BlasTrac. Hand grind or scarify all hard to reach areas. Blast should remove all surface laitance, existing coatings and any mastics giving a clean profiled concrete. Prime all areas with 10 mils of ARCOR™ EE-75 or EE-79 followed by a 20 mil Topcoat of ARCOR™ EE-75.
MIXING: Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade. Mix by Volume 3 parts Base to 2 part Activator or by weight 100 grams base to 59 grams activator.
THINNING: Never thin.
APPLICATION: All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate contamination.
Brush use medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Roller use good quality 1/4” nap on concrete.
Floor squeegee use hard rubber ‘notched’.
Plural Spray use .017-.019 tip, 2,000-2,500 PSI, Heat to 100ºF Base, 100ºF Activator. Airless Spray use .017-.021 tip, 2,000-2,500 PSI(Caution: Short Pot-Life) Conventional Spray: Not Recommended
APPLICATION TEMPERATURE: Material: Keep between 55 to 95ºF (13 to 35ºC). Substrate : Keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of the substrate and the coating should never exceed 10ºF (5ºC).
OVERCOAT/CURE TIME: Brush or Roller re-coat between 2 and 14 hours at 77ºF (25ºC).
Full cure before chemical exposure or high stress; 24 Hours at 77ºF. Force Cure: 12 hours at 150ºF (66ºC); 6 hours at 200ºF (93ºC).
CLEAN UP: Clean tools immediately after use with M.E.K., Acetone, 98+% Isopropyl Alcohol or similar
WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irritation persists seek medical attention. Consult the Product Safety Data Sheets (SDS) BEFORE USE!
The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Novolac Epoxy Technologies Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer.
Are you interested in this product?
Want to know more?
To place orders and/or obtain pricing information contact or call our offices below:
Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. ARCOR® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets and any other information as supplied in writing directly from manufacturers technical support.